سنسور NCB5-18GM40-N0

توضیحات محصول

سنسور نامور NCB5-18GM40-N0

Inductive sensor NCB5-18GM40-N0

• 5 mm flush
• Usable up to SIL 2 acc. to IEC 61508
• Datasheet excerpt: Technical data of NCB5-18GM40-N0

  General specifications
  Switching function	Normally closed (NC)
  Output type	NAMUR
  Rated operating distance	5 mm
  Installation	flush
  Assured operating distance	0 ... 4.05 mm
  Actual operating distance	4.5 ... 5.5 mm typ. 5 mm
  Reduction factor rAl	0.35
  Reduction factor rCu	0.3
  Reduction factor r304	0.74
  Nominal ratings
  Nominal voltage	8.2 V (Ri approx. 1 kΩ)
  Switching frequency	0 ... 400 Hz
  Hysteresis	1 ... 15 typ. 5 %
  Reverse polarity protection	reverse polarity protected
  Short-circuit protection	yes
  Current consumption
  	Measuring plate not detected	min. 3 mA
  	Measuring plate detected	≤ 1 mA
  Switching state indicator	all direction LED, yellow
  Functional safety related parameters
  MTTFd	2040 a
  Mission Time (TM)	20 a
  Diagnostic Coverage (DC)	0 %
  Compliance with standards and directives
  Standard conformity
  	NAMUR	EN 60947-5-6:2000 IEC 60947-5-6:1999
  	Electromagnetic compatibility	NE 21:2007
  Approvals and certificates
  FM approval
  	Control drawing	116-0165
  UL approval	cULus Listed, General Purpose
  CSA approval	cCSAus Listed, General Purpose
  CCC approval	CCC approval / marking not required for products rated ≤36 V
  Ambient conditions
  Ambient temperature	-25 ... 100 °C (-13 ... 212 °F)
  Storage temperature	-40 ... 100 °C (-40 ... 212 °F)
  Mechanical specifications
  Connection type	cable PVC , 2 m
  Core cross-section	0.75 mm2
  Housing material	Stainless steel 1.4305 / AISI 303
  Sensing face	PBT
  Housing diameter	18 mm
  Degree of protection	IP66 / IP67
  Cable
  	Bending radius	> 10 x cable diameter
  Equipment protection level Dc (tc)
  Instruction	Manual electrical apparatus for hazardous areas
  Device category 3D	for use in hazardous areas with combustible dust
  Certificate of Compliance	PF 15CERT3774 X
  CE marking	[*PD-Z02585A*]
  ATEX marking	II 3D Ex tc IIIC T80°C Dc The Ex-related marking can also be printed on the enclosed label.
  Standards	EN 60079-0:2012+A11:2013, EN 60079-31:2014 Protection by enclosure "tc" Some of the information in this instruction manual is more specific than the information provided in the datasheet.
  General	The corresponding datasheets, declarations of conformity, EC-type examination certificates, certifications, and control drawings, where applicable (see datasheets), form an integral part of this document. These documents can be found at www.pepperl-fuchs.com. The maximum surface temperature of the device was determined without a layer of dust on the apparatus. Some of the information in this instruction manual is more specific than the information provided in the datasheet.
  Installation, commissioning	Laws and/or regulations and standards governing the use or intended usage goal must be observed. If the Ex-relevant identification is printed exclusively on the adhesive label provided, this label must be affixed in the immediate vicinity of the sensor! The background surface to which the adhesivelabel is to be applied must be clean and free from grease! The applied label must be durable and remain legible, with due consideration of the possibility of chemical corrosion!
  Maintenance	No changes can be made to apparatus, which are operated in hazardous areas. Repairs to these apparatus are not possible.
  Special conditions
  	Minimum series resistance RV	A minimum series resistance RV is to be provided between the power supply voltage and the proximity switch in accordance with the following list. This can also be assured by using a switch amplifier.
  	Maximum operating voltage UBmax	The maximum permissible operating voltage UBmax must be restricted to the values given in the following list. Tolerances are not permitted.
  	Maximum permissible ambient temperature TUmax	Values can be obtained from the following list, depending on the max. operating voltage Ub max and the minimum series resistance Rv.
  	at UBmax=9 V, RV=562 Ω	61 °C (141.8 °F)
  	using an amplifier in accordance with EN 60947-5-6	61 °C (141.8 °F)
  	Protection from mechanical danger	The sensor must not be exposed to ANY FORM of mechanical danger.
  	Protection from UV light	The sensor and the connection cable must be protected from damaging UV-radiation. This can be achieved when the sensor is used in internal areas.
  	Protection of the connection cable	The connection cable must be prevented from being subjected to tension and torsional loading.
  	Electrostatic charge	Electrostatic charges must be avoided on the mechanical housing components. Dangerous electrostatic charges on the mechanical housing components can be avoided by incorporating these in the equipotential bonding. Do not attach the nameplate provided in areas where electrostatic charge can build up.
  General information
  Use in the hazardous area	see instruction manuals
  	Category	1G; 2G; 3G; 1D; 3D